Network Working Group R. Fielding Request for Comments: 2068 UC Irvine Category: Standards Track J. Gettys J. Mogul DEC H. Frystyk T. Berners-Lee MIT/LCS January 1997 Hypertext Transfer Protocol -- HTTP/1.1 Status of this Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited. Abstract The Hypertext Transfer Protocol (HTTP) is an application-level protocol for distributed, collaborative, hypermedia information systems. It is a generic, stateless, object-oriented protocol which can be used for many tasks, such as name servers and distributed object management systems, through extension of its request methods. A feature of HTTP is the typing and negotiation of data representation, allowing systems to be built independently of the data being transferred. HTTP has been in use by the World-Wide Web global information initiative since 1990. This specification defines the protocol referred to as "HTTP/1.1". Table of Contents 1 Introduction.............................................7 1.1 Purpose ..............................................7 1.2 Requirements .........................................7 1.3 Terminology ..........................................8 1.4 Overall Operation ...................................11 2 Notational Conventions and Generic Grammar..............13 2.1 Augmented BNF .......................................13 2.2 Basic Rules .........................................15 3 Protocol Parameters.....................................17 3.1 HTTP Version ........................................17 Fielding, et. al. Standards Track [Page 1] RFC 2068 HTTP/1.1 January 1997 3.2 Uniform Resource Identifiers ........................18 3.2.1 General Syntax ...................................18 3.2.2 http URL .........................................19 3.2.3 URI Comparison ...................................20 3.3 Date/Time Formats ...................................21 3.3.1 Full Date ........................................21 3.3.2 Delta Seconds ....................................22 3.4 Character Sets ......................................22 3.5 Content Codings .....................................23 3.6 Transfer Codings ....................................24 3.7 Media Types .........................................25 3.7.1 Canonicalization and Text Defaults ...............26 3.7.2 Multipart Types ..................................27 3.8 Product Tokens ......................................28 3.9 Quality Values ......................................28 3.10 Language Tags ......................................28 3.11 Entity Tags ........................................29 3.12 Range Units ........................................30 4 HTTP Message............................................30 4.1 Message Types .......................................30 4.2 Message Headers .....................................31 4.3 Message Body ........................................32 4.4 Message Length ......................................32 4.5 General Header Fields ...............................34 5 Request.................................................34 5.1 Request-Line ........................................34 5.1.1 Method ...........................................35 5.1.2 Request-URI ......................................35 5.2 The Resource Identified by a Request ................37 5.3 Request Header Fields ...............................37 6 Response................................................38 6.1 Status-Line .........................................38 6.1.1 Status Code and Reason Phrase ....................39 6.2 Response Header Fields ..............................41 7 Entity..................................................41 7.1 Entity Header Fields ................................41 7.2 Entity Body .........................................42 7.2.1 Type .............................................42 7.2.2 Length ...........................................43 8 Connections.............................................43 8.1 Persistent Connections ..............................43 8.1.1 Purpose ..........................................43 8.1.2 Overall Operation ................................44 8.1.3 Proxy Servers ....................................45 8.1.4 Practical Considerations .........................45 8.2 Message Transmission Requirements ...................46 9 Method Definitions......................................48 9.1 Safe and Idempotent Methods .........................48 Fielding, et. al. Standards Track [Page 2] RFC 2068 HTTP/1.1 January 1997 9.1.1 Safe Methods .....................................48 9.1.2 Idempotent Methods ...............................49 9.2 OPTIONS .............................................49 9.3 GET .................................................50 9.4 HEAD ................................................50 9.5 POST ................................................51 9.6 PUT .................................................52 9.7 DELETE ..............................................53 9.8 TRACE ...............................................53 10 Status Code Definitions................................53 10.1 Informational 1xx ..................................54 10.1.1 100 Continue ....................................54 10.1.2 101 Switching Protocols .........................54 10.2 Successful 2xx .....................................54 10.2.1 200 OK ..........................................54 10.2.2 201 Created .....................................55 10.2.3 202 Accepted ....................................55 10.2.4 203 Non-Authoritative Information ...............55 10.2.5 204 No Content ..................................55 10.2.6 205 Reset Content ...............................56 10.2.7 206 Partial Content .............................56 10.3 Redirection 3xx ....................................56 10.3.1 300 Multiple Choices ............................57 10.3.2 301 Moved Permanently ...........................57 10.3.3 302 Moved Temporarily ...........................58 10.3.4 303 See Other ...................................58 10.3.5 304 Not Modified ................................58 10.3.6 305 Use Proxy ...................................59 10.4 Client Error 4xx ...................................59 10.4.1 400 Bad Request .................................60 10.4.2 401 Unauthorized ................................60 10.4.3 402 Payment Required ............................60 10.4.4 403 Forbidden ...................................60 10.4.5 404 Not Found ...................................60 10.4.6 405 Method Not Allowed ..........................61 10.4.7 406 Not Acceptable ..............................61 10.4.8 407 Proxy Authentication Required ...............61 10.4.9 408 Request Timeout .............................62 10.4.10 409 Conflict ...................................62 10.4.11 410 Gone .......................................62 10.4.12 411 Length Required ............................63 10.4.13 412 Precondition Failed ........................63 10.4.14 413 Request Entity Too Large ...................63 10.4.15 414 Request-URI Too Long .......................63 10.4.16 415 Unsupported Media Type .....................63 10.5 Server Error 5xx ...................................64 10.5.1 500 Internal Server Error .......................64 10.5.2 501 Not Implemented .............................64 Fielding, et. al. Standards Track [Page 3] RFC 2068 HTTP/1.1 January 1997 10.5.3 502 Bad Gateway .................................64 10.5.4 503 Service Unavailable .........................64 10.5.5 504 Gateway Timeout .............................64 10.5.6 505 HTTP Version Not Supported ..................65 11 Access Authentication..................................65 11.1 Basic Authentication Scheme ........................66 11.2 Digest Authentication Scheme .......................67 12 Content Negotiation....................................67 12.1 Server-driven Negotiation ..........................68 12.2 Agent-driven Negotiation ...........................69 12.3 Transparent Negotiation ............................70 13 Caching in HTTP........................................70 13.1.1 Cache Correctness ...............................72 13.1.2 Warnings ........................................73 13.1.3 Cache-control Mechanisms ........................74 13.1.4 Explicit User Agent Warnings ....................74 13.1.5 Exceptions to the Rules and Warnings ............75 13.1.6 Client-controlled Behavior ......................75 13.2 Expiration Model ...................................75 13.2.1 Server-Specified Expiration .....................75 13.2.2 Heuristic Expiration ............................76 13.2.3 Age Calculations ................................77 13.2.4 Expiration Calculations .........................79 13.2.5 Disambiguating Expiration Values ................80 13.2.6 Disambiguating Multiple Responses ...............80 13.3 Validation Model ...................................81 13.3.1 Last-modified Dates .............................82 13.3.2 Entity Tag Cache Validators .....................82 13.3.3 Weak and Strong Validators ......................82 13.3.4 Rules for When to Use Entity Tags and Last- modified Dates..........................................85 13.3.5 Non-validating Conditionals .....................86 13.4 Response Cachability ...............................86 13.5 Constructing Responses From Caches .................87 13.5.1 End-to-end and Hop-by-hop Headers ...............88 13.5.2 Non-modifiable Headers ..........................88 13.5.3 Combining Headers ...............................89 13.5.4 Combining Byte Ranges ...........................90 13.6 Caching Negotiated Responses .......................90 13.7 Shared and Non-Shared Caches .......................91 13.8 Errors or Incomplete Response Cache Behavior .......91 13.9 Side Effects of GET and HEAD .......................92 13.10 Invalidation After Updates or Deletions ...........92 13.11 Write-Through Mandatory ...........................93 13.12 Cache Replacement .................................93 13.13 History Lists .....................................93 14 Header Field Definitions...............................94 14.1 Accept .............................................95 Fielding, et. al. Standards Track [Page 4] RFC 2068 HTTP/1.1 January 1997 14.2 Accept-Charset .....................................97 14.3 Accept-Encoding ....................................97 14.4 Accept-Language ....................................98 14.5 Accept-Ranges ......................................99 14.6 Age ................................................99 14.7 Allow .............................................100 14.8 Authorization .....................................100 14.9 Cache-Control .....................................101 14.9.1 What is Cachable ...............................103 14.9.2 What May be Stored by Caches ...................103 14.9.3 Modifications of the Basic Expiration Mechanism 104 14.9.4 Cache Revalidation and Reload Controls .........105 14.9.5 No-Transform Directive .........................107 14.9.6 Cache Control Extensions .......................108 14.10 Connection .......................................109 14.11 Content-Base .....................................109 14.12 Content-Encoding .................................110 14.13 Content-Language .................................110 14.14 Content-Length ...................................111 14.15 Content-Location .................................112 14.16 Content-MD5 ......................................113 14.17 Content-Range ....................................114 14.18 Content-Type .....................................116 14.19 Date .............................................116 14.20 ETag .............................................117 14.21 Expires ..........................................117 14.22 From .............................................118 14.23 Host .............................................119 14.24 If-Modified-Since ................................119 14.25 If-Match .........................................121 14.26 If-None-Match ....................................122 14.27 If-Range .........................................123 14.28 If-Unmodified-Since ..............................124 14.29 Last-Modified ....................................124 14.30 Location .........................................125 14.31 Max-Forwards .....................................125 14.32 Pragma ...........................................126 14.33 Proxy-Authenticate ...............................127 14.34 Proxy-Authorization ..............................127 14.35 Public ...........................................127 14.36 Range ............................................128 14.36.1 Byte Ranges ...................................128 14.36.2 Range Retrieval Requests ......................130 14.37 Referer ..........................................131 14.38 Retry-After ......................................131 14.39 Server ...........................................132 14.40 Transfer-Encoding ................................132 14.41 Upgrade ..........................................132 Fielding, et. al. Standards Track [Page 5] RFC 2068 HTTP/1.1 January 1997 14.42 User-Agent .......................................134 14.43 Vary .............................................134 14.44 Via ..............................................135 14.45 Warning ..........................................137 14.46 WWW-Authenticate .................................139 15 Security Considerations...............................139 15.1 Authentication of Clients .........................139 15.2 Offering a Choice of Authentication Schemes .......140 15.3 Abuse of Server Log Information ...................141 15.4 Transfer of Sensitive Information .................141 15.5 Attacks Based On File and Path Names ..............142 15.6 Personal Information ..............................143 15.7 Privacy Issues Connected to Accept Headers ........143 15.8 DNS Spoofing ......................................144 15.9 Location Headers and Spoofing .....................144 16 Acknowledgments.......................................144 17 References............................................146 18 Authors' Addresses....................................149 19 Appendices............................................150 19.1 Internet Media Type message/http ..................150 19.2 Internet Media Type multipart/byteranges ..........150 19.3 Tolerant Applications .............................151 19.4 Differences Between HTTP Entities and MIME Entities...........................................152 19.4.1 Conversion to Canonical Form ...................152 19.4.2 Conversion of Date Formats .....................153 19.4.3 Introduction of Content-Encoding ...............153 19.4.4 No Content-Transfer-Encoding ...................153 19.4.5 HTTP Header Fields in Multipart Body-Parts .....153 19.4.6 Introduction of Transfer-Encoding ..............154 19.4.7 MIME-Version ...................................154 19.5 Changes from HTTP/1.0 .............................154 19.5.1 Changes to Simplify Multi-homed Web Servers and Conserve IP Addresses .................................155 19.6 Additional Features ...............................156 19.6.1 Additional Request Methods .....................156 19.6.2 Additional Header Field Definitions ............156 19.7 Compatibility with Previous Versions ..............160 19.7.1 Compatibility with HTTP/1.0 Persistent Connections............................................161 Fielding, et. al. Standards Track [Page 6] RFC 2068 HTTP/1.1 January 1997 1 Introduction 1.1 Purpose The Hypertext Transfer Protocol (HTTP) is an application-level protocol for distributed, collaborative, hypermedia information systems. HTTP has been in use by the World-Wide Web global information initiative since 1990. The first version of HTTP, referred to as HTTP/0.9, was a simple protocol for raw data transfer across the Internet. HTTP/1.0, as defined by RFC 1945 [6], improved the protocol by allowing messages to be in the format of MIME-like messages, containing metainformation about the data transferred and modifiers on the request/response semantics. However, HTTP/1.0 does not sufficiently take into consideration the effects of hierarchical proxies, caching, the need for persistent connections, and virtual hosts. In addition, the proliferation of incompletely-implemented applications calling themselves "HTTP/1.0" has necessitated a protocol version change in order for two communicating applications to determine each other's true capabilities. This specification defines the protocol referred to as "HTTP/1.1". This protocol includes more stringent requirements than HTTP/1.0 in order to ensure reliable implementation of its features. Practical information systems require more functionality than simple retrieval, including search, front-end update, and annotation. HTTP allows an open-ended set of methods that indicate the purpose of a request. It builds on the discipline of reference provided by the Uniform Resource Identifier (URI) [3][20], as a location (URL) [4] or name (URN) , for indicating the resource to which a method is to be applied. Messages are passed in a format similar to that used by Internet mail as defined by the Multipurpose Internet Mail Extensions (MIME). HTTP is also used as a generic protocol for communication between user agents and proxies/gateways to other Internet systems, including those supported by the SMTP [16], NNTP [13], FTP [18], Gopher [2], and WAIS [10] protocols. In this way, HTTP allows basic hypermedia access to resources available from diverse applications. 1.2 Requirements This specification uses the same words as RFC 1123 [8] for defining the significance of each particular requirement. These words are: MUST This word or the adjective "required" means that the item is an absolute requirement of the specification. Fielding, et. al. Standards Track [Page 7] RFC 2068 HTTP/1.1 January 1997 SHOULD This word or the adjective "recommended" means that there may exist valid reasons in particular circumstances to ignore this item, but the full implications should be understood and the case carefully weighed before choosing a different course. MAY This word or the adjective "optional" means that this item is truly optional. One vendor may choose to include the item because a particular marketplace requires it or because it enhances the product, for example; another vendor may omit the same item. An implementation is not compliant if it fails to satisfy one or more of the MUST requirements for the protocols it implements. An implementation that satisfies all the MUST and all the SHOULD requirements for its protocols is said to be "unconditionally compliant"; one that satisfies all the MUST requirements but not all the SHOULD requirements for its protocols is said to be "conditionally compliant." 1.3 Terminology This specification uses a number of terms to refer to the roles played by participants in, and objects of, the HTTP communication. connection A transport layer virtual circuit established between two programs for the purpose of communication. message The basic unit of HTTP communication, consisting of a structured sequence of octets matching the syntax defined in section 4 and transmitted via the connection. request An HTTP request message, as defined in section 5. response An HTTP response message, as defined in section 6. resource A network data object or service that can be identified by a URI, as defined in section 3.2. Resources may be available in multiple representations (e.g. multiple languages, data formats, size, resolutions) or vary in other ways. Fielding, et. al. Standards Track [Page 8] RFC 2068 HTTP/1.1 January 1997 entity The information transferred as the payload of a request or response. An entity consists of metainformation in the form of entity-header fields and content in the form of an entity-body, as described in section 7. representation An entity included with a response that is subject to content negotiation, as described in section 12. There may exist multiple representations associated with a particular response status. content negotiation The mechanism for selecting the appropriate representation when servicing a request, as described in section 12. The representation of entities in any response can be negotiated (including error responses). variant A resource may have one, or more than one, representation(s) associated with it at any given instant. Each of these representations is termed a `variant.' Use of the term `variant' does not necessarily imply that the resource is subject to content negotiation. client A program that establishes connections for the purpose of sending requests. user agent The client which initiates a request. These are often browsers, editors, spiders (web-traversing robots), or other end user tools. server An application program that accepts connections in order to service requests by sending back responses. Any given program may be capable of being both a client and a server; our use of these terms refers only to the role being performed by the program for a particular connection, rather than to the program's capabilities in general. Likewise, any server may act as an origin server, proxy, gateway, or tunnel, switching behavior based on the nature of each request. origin server The server on which a given resource resides or is to be created. Fielding, et. al. Standards Track [Page 9] RFC 2068 HTTP/1.1 January 1997 proxy An intermediary program which acts as both a server and a client for the purpose of making requests on behalf of other clients. Requests are serviced internally or by passing them on, with possible translation, to other servers. A proxy must implement both the client and server requirements of this specification. gateway A server which acts as an intermediary for some other server. Unlike a proxy, a gateway receives requests as if it were the origin server for the requested resource; the requesting client may not be aware that it is communicating with a gateway. tunnel An intermediary program which is acting as a blind relay between two connections. Once active, a tunnel is not considered a party to the HTTP communication, though the tunnel may have been initiated by an HTTP request. The tunnel ceases to exist when both ends of the relayed connections are closed. cache A program's local store of response messages and the subsystem that controls its message storage, retrieval, and deletion. A cache stores cachable responses in order to reduce the response time and network bandwidth consumption on future, equivalent requests. Any client or server may include a cache, though a cache cannot be used by a server that is acting as a tunnel. cachable A response is cachable if a cache is allowed to store a copy of the response message for use in answering subsequent requests. The rules for determining the cachability of HTTP responses are defined in section 13. Even if a resource is cachable, there may be additional constraints on whether a cache can use the cached copy for a particular request. first-hand A response is first-hand if it comes directly and without unnecessary delay from the origin server, perhaps via one or more proxies. A response is also first-hand if its validity has just been checked directly with the origin server. explicit expiration time The time at which the origin server intends that an entity should no longer be returned by a cache without further validation. Fielding, et. al. Standards Track [Page 10] RFC 2068 HTTP/1.1 January 1997 heuristic expiration time An expiration time assigned by a cache when no explicit expiration time is available. age The age of a response is the time since it was sent by, or successfully validated with, the origin server. freshness lifetime The length of time between the generation of a response and its expiration time. fresh A response is fresh if its age has not yet exceeded its freshness lifetime. stale A response is stale if its age has passed its freshness lifetime. semantically transparent A cache behaves in a "semantically transparent" manner, with respect to a particular response, when its use affects neither the requesting client nor the origin server, except to improve performance. When a cache is semantically transparent, the client receives exactly the same response (except for hop-by-hop headers) that it would have received had its request been handled directly by the origin server. validator A protocol element (e.g., an entity tag or a Last-Modified time) that is used to find out whether a cache entry is an equivalent copy of an entity. 1.4 Overall Operation The HTTP protocol is a request/response protocol. A client sends a request to the server in the form of a request method, URI, and protocol version, followed by a MIME-like message containing request modifiers, client information, and possible body content over a connection with a server. The server responds with a status line, including the message's protocol version and a success or error code, followed by a MIME-like message containing server information, entity metainformation, and possible entity-body content. The relationship between HTTP and MIME is described in appendix 19.4. Fielding, et. al. Standards Track [Page 11] RFC 2068 HTTP/1.1 January 1997 Most HTTP communication is initiated by a user agent and consists of a request to be applied to a resource on some origin server. In the simplest case, this may be accomplished via a single connection (v) between the user agent (UA) and the origin server (O). request chain ------------------------> UA -------------------v------------------- O <----------------------- response chain A more complicated situation occurs when one or more intermediaries are present in the request/response chain. There are three common forms of intermediary: proxy, gateway, and tunnel. A proxy is a forwarding agent, receiving requests for a URI in its absolute form, rewriting all or part of the message, and forwarding the reformatted request toward the server identified by the URI. A gateway is a receiving agent, acting as a layer above some other server(s) and, if necessary, translating the requests to the underlying server's protocol. A tunnel acts as a relay point between two connections without changing the messages; tunnels are used when the communication needs to pass through an intermediary (such as a firewall) even when the intermediary cannot understand the contents of the messages. request chain --------------------------------------> UA -----v----- A -----v----- B -----v----- C -----v----- O <------------------------------------- response chain The figure above shows three intermediaries (A, B, and C) between the user agent and origin server. A request or response message that travels the whole chain will pass through four separate connections. This distinction is important because some HTTP communication options may apply only to the connection with the nearest, non-tunnel neighbor, only to the end-points of the chain, or to all connections along the chain. Although the diagram is linear, each participant may be engaged in multiple, simultaneous communications. For example, B may be receiving requests from many clients other than A, and/or forwarding requests to servers other than C, at the same time that it is handling A's request. Any party to the communication which is not acting as a tunnel may employ an internal cache for handling requests. The effect of a cache is that the request/response chain is shortened if one of the participants along the chain has a cached response applicable to that request. The following illustrates the resulting chain if B has a cached copy of an earlier response from O (via C) for a request which has not been cached by UA or A. Fielding, et. al. Standards Track [Page 12] RFC 2068 HTTP/1.1 January 1997 request chain ----------> UA -----v----- A -----v----- B - - - - - - C - - - - - - O <--------- response chain Not all responses are usefully cachable, and some requests may contain modifiers which place special requirements on cache behavior. HTTP requirements for cache behavior and cachable responses are defined in section 13. In fact, there are a wide variety of architectures and configurations of caches and proxies currently being experimented with or deployed across the World Wide Web; these systems include national hierarchies of proxy caches to save transoceanic bandwidth, systems that broadcast or multicast cache entries, organizations that distribute subsets of cached data via CD-ROM, and so on. HTTP systems are used in corporate intranets over high-bandwidth links, and for access via PDAs with low-power radio links and intermittent connectivity. The goal of HTTP/1.1 is to support the wide diversity of configurations already deployed while introducing protocol constructs that meet the needs of those who build web applications that require high reliability and, failing that, at least reliable indications of failure. HTTP communication usually takes place over TCP/IP connections. The default port is TCP 80, but other ports can be used. This does not preclude HTTP from being implemented on top of any other protocol on the Internet, or on other networks. HTTP only presumes a reliable transport; any protocol that provides such guarantees can be used; the mapping of the HTTP/1.1 request and response structures onto the transport data units of the protocol in question is outside the scope of this specification. In HTTP/1.0, most implementations used a new connection for each request/response exchange. In HTTP/1.1, a connection may be used for one or more request/response exchanges, although connections may be closed for a variety of reasons (see section 8.1). 2 Notational Conventions and Generic Grammar 2.1 Augmented BNF All of the mechanisms specified in this document are described in both prose and an augmented Backus-Naur Form (BNF) similar to that used by RFC 822 [9]. Implementers will need to be familiar with the notation in order to understand this specification. The augmented BNF includes the following constructs: Fielding, et. al. Standards Track [Page 13] RFC 2068 HTTP/1.1 January 1997 name = definition The name of a rule is simply the name itself (without any enclosing "<" and ">") and is separated from its definition by the equal "=" character. Whitespace is only significant in that indentation of continuation lines is used to indicate a rule definition that spans more than one line. Certain basic rules are in uppercase, such as SP, LWS, HT, CRLF, DIGIT, ALPHA, etc. Angle brackets are used within definitions whenever their presence will facilitate discerning the use of rule names. "literal" Quotation marks surround literal text. Unless stated otherwise, the text is case-insensitive. rule1 | rule2 Elements separated by a bar ("|") are alternatives, e.g., "yes | no" will accept yes or no. (rule1 rule2) Elements enclosed in parentheses are treated as a single element. Thus, "(elem (foo | bar) elem)" allows the token sequences "elem foo elem" and "elem bar elem". *rule The character "*" preceding an element indicates repetition. The full form is "*element" indicating at least and at most occurrences of element. Default values are 0 and infinity so that "*(element)" allows any number, including zero; "1*element" requires at least one; and "1*2element" allows one or two. [rule] Square brackets enclose optional elements; "[foo bar]" is equivalent to "*1(foo bar)". N rule Specific repetition: "(element)" is equivalent to "*(element)"; that is, exactly occurrences of (element). Thus 2DIGIT is a 2-digit number, and 3ALPHA is a string of three alphabetic characters. #rule A construct "#" is defined, similar to "*", for defining lists of elements. The full form is "#element " indicating at least and at most elements, each separated by one or more commas (",") and optional linear whitespace (LWS). This makes the usual form of lists very easy; a rule such as "( *LWS element *( *LWS "," *LWS element )) " can be shown as "1#element". Wherever this construct is used, null elements are allowed, but do not contribute Fielding, et. al. Standards Track [Page 14] RFC 2068 HTTP/1.1 January 1997 to the count of elements present. That is, "(element), , (element) " is permitted, but counts as only two elements. Therefore, where at least one element is required, at least one non-null element must be present. Default values are 0 and infinity so that "#element" allows any number, including zero; "1#element" requires at least one; and "1#2element" allows one or two. ; comment A semi-colon, set off some distance to the right of rule text, starts a comment that continues to the end of line. This is a simple way of including useful notes in parallel with the specifications. implied *LWS The grammar described by this specification is word-based. Except where noted otherwise, linear whitespace (LWS) can be included between any two adjacent words (token or quoted-string), and between adjacent tokens and delimiters (tspecials), without changing the interpretation of a field. At least one delimiter (tspecials) must exist between any two tokens, since they would otherwise be interpreted as a single token. 2.2 Basic Rules The following rules are used throughout this specification to describe basic parsing constructs. The US-ASCII coded character set is defined by ANSI X3.4-1986 [21]. OCTET = CHAR = UPALPHA = LOALPHA = ALPHA = UPALPHA | LOALPHA DIGIT = CTL = CR = LF = SP = HT = <"> = Fielding, et. al. Standards Track [Page 15] RFC 2068 HTTP/1.1 January 1997 HTTP/1.1 defines the sequence CR LF as the end-of-line marker for all protocol elements except the entity-body (see appendix 19.3 for tolerant applications). The end-of-line marker within an entity-body is defined by its associated media type, as described in section 3.7. CRLF = CR LF HTTP/1.1 headers can be folded onto multiple lines if the continuation line begins with a space or horizontal tab. All linear white space, including folding, has the same semantics as SP. LWS = [CRLF] 1*( SP | HT ) The TEXT rule is only used for descriptive field contents and values that are not intended to be interpreted by the message parser. Words of *TEXT may contain characters from character sets other than ISO 8859-1 [22] only when encoded according to the rules of RFC 1522 [14]. TEXT = Hexadecimal numeric characters are used in several protocol elements. HEX = "A" | "B" | "C" | "D" | "E" | "F" | "a" | "b" | "c" | "d" | "e" | "f" | DIGIT Many HTTP/1.1 header field values consist of words separated by LWS or special characters. These special characters MUST be in a quoted string to be used within a parameter value. token = 1* tspecials = "(" | ")" | "<" | ">" | "@" | "," | ";" | ":" | "\" | <"> | "/" | "[" | "]" | "?" | "=" | "{" | "}" | SP | HT Comments can be included in some HTTP header fields by surrounding the comment text with parentheses. Comments are only allowed in fields containing "comment" as part of their field value definition. In all other fields, parentheses are considered part of the field value. comment = "(" *( ctext | comment ) ")" ctext = Fielding, et. al. Standards Track [Page 16] RFC 2068 HTTP/1.1 January 1997 A string of text is parsed as a single word if it is quoted using double-quote marks. quoted-string = ( <"> *(qdtext) <"> ) qdtext = > The backslash character ("\") may be used as a single-character quoting mechanism only within quoted-string and comment constructs. quoted-pair = "\" CHAR 3 Protocol Parameters 3.1 HTTP Version HTTP uses a "." numbering scheme to indicate versions of the protocol. The protocol versioning policy is intended to allow the sender to indicate the format of a message and its capacity for understanding further HTTP communication, rather than the features obtained via that communication. No change is made to the version number for the addition of message components which do not affect communication behavior or which only add to extensible field values. The number is incremented when the changes made to the protocol add features which do not change the general message parsing algorithm, but which may add to the message semantics and imply additional capabilities of the sender. The number is incremented when the format of a message within the protocol is changed. The version of an HTTP message is indicated by an HTTP-Version field in the first line of the message. HTTP-Version = "HTTP" "/" 1*DIGIT "." 1*DIGIT Note that the major and minor numbers MUST be treated as separate integers and that each may be incremented higher than a single digit. Thus, HTTP/2.4 is a lower version than HTTP/2.13, which in turn is lower than HTTP/12.3. Leading zeros MUST be ignored by recipients and MUST NOT be sent. Applications sending Request or Response messages, as defined by this specification, MUST include an HTTP-Version of "HTTP/1.1". Use of this version number indicates that the sending application is at least conditionally compliant with this specification. The HTTP version of an application is the highest HTTP version for which the application is at least conditionally compliant. Fielding, et. al. Standards Track [Page 17] RFC 2068 HTTP/1.1 January 1997 Proxy and gateway applications must be careful when forwarding messages in protocol versions different from that of the application. Since the protocol version indicates the protocol capability of the sender, a proxy/gateway MUST never send a message with a version indicator which is greater than its actual version; if a higher version request is received, the proxy/gateway MUST either downgrade the request version, respond with an error, or switch to tunnel behavior. Requests with a version lower than that of the proxy/gateway's version MAY be upgraded before being forwarded; the proxy/gateway's response to that request MUST be in the same major version as the request. Note: Converting between versions of HTTP may involve modification of header fields required or forbidden by the versions involved. 3.2 Uniform Resource Identifiers URIs have been known by many names: WWW addresses, Universal Document Identifiers, Universal Resource Identifiers , and finally the combination of Uniform Resource Locators (URL) and Names (URN). As far as HTTP is concerned, Uniform Resource Identifiers are simply formatted strings which identify--via name, location, or any other characteristic--a resource. 3.2.1 General Syntax URIs in HTTP can be represented in absolute form or relative to some known base URI, depending upon the context of their use. The two forms are differentiated by the fact that absolute URIs always begin with a scheme name followed by a colon. URI = ( absoluteURI | relativeURI ) [ "#" fragment ] absoluteURI = scheme ":" *( uchar | reserved ) relativeURI = net_path | abs_path | rel_path net_path = "//" net_loc [ abs_path ] abs_path = "/" rel_path rel_path = [ path ] [ ";" params ] [ "?" query ] path = fsegment *( "/" segment ) fsegment = 1*pchar segment = *pchar params = param *( ";" param ) param = *( pchar | "/" ) Fielding, et. al. Standards Track [Page 18] RFC 2068 HTTP/1.1 January 1997 scheme = 1*( ALPHA | DIGIT | "+" | "-" | "." ) net_loc = *( pchar | ";" | "?" ) query = *( uchar | reserved ) fragment = *( uchar | reserved ) pchar = uchar | ":" | "@" | "&" | "=" | "+" uchar = unreserved | escape unreserved = ALPHA | DIGIT | safe | extra | national escape = "%" HEX HEX reserved = ";" | "/" | "?" | ":" | "@" | "&" | "=" | "+" extra = "!" | "*" | "'" | "(" | ")" | "," safe = "$" | "-" | "_" | "." unsafe = CTL | SP | <"> | "#" | "%" | "<" | ">" national = For definitive information on URL syntax and semantics, see RFC 1738 [4] and RFC 1808 [11]. The BNF above includes national characters not allowed in valid URLs as specified by RFC 1738, since HTTP servers are not restricted in the set of unreserved characters allowed to represent the rel_path part of addresses, and HTTP proxies may receive requests for URIs not defined by RFC 1738. The HTTP protocol does not place any a priori limit on the length of a URI. Servers MUST be able to handle the URI of any resource they serve, and SHOULD be able to handle URIs of unbounded length if they provide GET-based forms that could generate such URIs. A server SHOULD return 414 (Request-URI Too Long) status if a URI is longer than the server can handle (see section 10.4.15). Note: Servers should be cautious about depending on URI lengths above 255 bytes, because some older client or proxy implementations may not properly support these lengths. 3.2.2 http URL The "http" scheme is used to locate network resources via the HTTP protocol. This section defines the scheme-specific syntax and semantics for http URLs. Fielding, et. al. Standards Track [Page 19] RFC 2068 HTTP/1.1 January 1997 http_URL = "http:" "//" host [ ":" port ] [ abs_path ] host = port = *DIGIT If the port is empty or not given, port 80 is assumed. The semantics are that the identified resource is located at the server listening for TCP connections on that port of that host, and the Request-URI for the resource is abs_path. The use of IP addresses in URL's SHOULD be avoided whenever possible (see RFC 1900 [24]). If the abs_path is not present in the URL, it MUST be given as "/" when used as a Request-URI for a resource (section 5.1.2). 3.2.3 URI Comparison When comparing two URIs to decide if they match or not, a client SHOULD use a case-sensitive octet-by-octet comparison of the entire URIs, with these exceptions: o A port that is empty or not given is equivalent to the default port for that URI; o Comparisons of host names MUST be case-insensitive; o Comparisons of scheme names MUST be case-insensitive; o An empty abs_path is equivalent to an abs_path of "/". Characters other than those in the "reserved" and "unsafe" sets (see section 3.2) are equivalent to their ""%" HEX HEX" encodings. For example, the following three URIs are equivalent: http://abc.com:80/~smith/home.html http://ABC.com/%7Esmith/home.html http://ABC.com:/%7esmith/home.html Fielding, et. al. Standards Track [Page 20] RFC 2068 HTTP/1.1 January 1997 3.3 Date/Time Formats 3.3.1 Full Date HTTP applications have historically allowed three different formats for the representation of date/time stamps: Sun, 06 Nov 1994 08:49:37 GMT ; RFC 822, updated by RFC 1123 Sunday, 06-Nov-94 08:49:37 GMT ; RFC 850, obsoleted by RFC 1036 Sun Nov 6 08:49:37 1994 ; ANSI C's asctime() format The first format is preferred as an Internet standard and represents a fixed-length subset of that defined by RFC 1123 (an update to RFC 822). The second format is in common use, but is based on the obsolete RFC 850 [12] date format and lacks a four-digit year. HTTP/1.1 clients and servers that parse the date value MUST accept all three formats (for compatibility with HTTP/1.0), though they MUST only generate the RFC 1123 format for representing HTTP-date values in header fields. Note: Recipients of date values are encouraged to be robust in accepting date values that may have been sent by non-HTTP applications, as is sometimes the case when retrieving or posting messages via proxies/gateways to SMTP or NNTP. All HTTP date/time stamps MUST be represented in Greenwich Mean Time (GMT), without exception. This is indicated in the first two formats by the inclusion of "GMT" as the three-letter abbreviation for time zone, and MUST be assumed when reading the asctime format. HTTP-date = rfc1123-date | rfc850-date | asctime-date rfc1123-date = wkday "," SP date1 SP time SP "GMT" rfc850-date = weekday "," SP date2 SP time SP "GMT" asctime-date = wkday SP date3 SP time SP 4DIGIT date1 = 2DIGIT SP month SP 4DIGIT ; day month year (e.g., 02 Jun 1982) date2 = 2DIGIT "-" month "-" 2DIGIT ; day-month-year (e.g., 02-Jun-82) date3 = month SP ( 2DIGIT | ( SP 1DIGIT )) ; month day (e.g., Jun 2) time = 2DIGIT ":" 2DIGIT ":" 2DIGIT ; 00:00:00 - 23:59:59 wkday = "Mon" | "Tue" | "Wed" | "Thu" | "Fri" | "Sat" | "Sun" Fielding, et. al. Standards Track [Page 21] RFC 2068 HTTP/1.1 January 1997 weekday = "Monday" | "Tuesday" | "Wednesday" | "Thursday" | "Friday" | "Saturday" | "Sunday" month = "Jan" | "Feb" | "Mar" | "Apr" | "May" | "Jun" | "Jul" | "Aug" | "Sep" | "Oct" | "Nov" | "Dec" Note: HTTP requirements for the date/time stamp format apply only to their usage within the protocol stream. Clients and servers are not required to use these formats for user presentation, request logging, etc. 3.3.2 Delta Seconds Some HTTP header fields allow a time value to be specified as an integer number of seconds, represented in decimal, after the time that the message was received. delta-seconds = 1*DIGIT 3.4 Character Sets HTTP uses the same definition of the term "character set" as that described for MIME: The term "character set" is used in this document to refer to a method used with one or more tables to convert a sequence of octets into a sequence of characters. Note that unconditional conversion in the other direction is not required, in that not all characters may be available in a given character set and a character set may provide more than one sequence of octets to represent a particular character. This definition is intended to allow various kinds of character encodings, from simple single-table mappings such as US- ASCII to complex table switching methods such as those that use ISO 2022's techniques. However, the definition associated with a MIME character set name MUST fully specify the mapping to be performed from octets to characters. In particular, use of external profiling information to determine the exact mapping is not permitted. Note: This use of the term "character set" is more commonly referred to as a "character encoding." However, since HTTP and MIME share the same registry, it is important that the terminology also be shared. Fielding, et. al. Standards Track [Page 22] RFC 2068 HTTP/1.1 January 1997 HTTP character sets are identified by case-insensitive tokens. The complete set of tokens is defined by the IANA Character Set registry [19]. charset = token Although HTTP allows an arbitrary token to be used as a charset value, any token that has a predefined value within the IANA Character Set registry MUST represent the character set defined by that registry. Applications SHOULD limit their use of character sets to those defined by the IANA registry. 3.5 Content Codings Content coding values indicate an encoding transformation that has been or can be applied to an entity. Content codings are primarily used to allow a document to be compressed or otherwise usefully transformed without losing the identity of its underlying media type and without loss of information. Frequently, the entity is stored in coded form, transmitted directly, and only decoded by the recipient. content-coding = token All content-coding values are case-insensitive. HTTP/1.1 uses content-coding values in the Accept-Encoding (section 14.3) and Content-Encoding (section 14.12) header fields. Although the value describes the content-coding, what is more important is that it indicates what decoding mechanism will be required to remove the encoding. The Internet Assigned Numbers Authority (IANA) acts as a registry for content-coding value tokens. Initially, the registry contains the following tokens: gzip An encoding format produced by the file compression program "gzip" (GNU zip) as described in RFC 1952 [25]. This format is a Lempel- Ziv coding (LZ77) with a 32 bit CRC. compress The encoding format produced by the common UNIX file compression program "compress". This format is an adaptive Lempel-Ziv-Welch coding (LZW). Fielding, et. al. Standards Track [Page 23] RFC 2068 HTTP/1.1 January 1997 Note: Use of program names for the identification of encoding formats is not desirable and should be discouraged for future encodings. Their use here is representative of historical practice, not good design. For compatibility with previous implementations of HTTP, applications should consider "x-gzip" and "x-compress" to be equivalent to "gzip" and "compress" respectively. deflate The "zlib" format defined in RFC 1950[31] in combination with the "deflate" compression mechanism described in RFC 1951[29]. New content-coding value tokens should be registered; to allow interoperability between clients and servers, specifications of the content coding algorithms needed to implement a new value should be publicly available and adequate for independent implementation, and conform to the purpose of content coding defined in this section. 3.6 Transfer Codings Transfer coding values are used to indicate an encoding transformation that has been, can be, or may need to be applied to an entity-body in order to ensure "safe transport" through the network. This differs from a content coding in that the transfer coding is a property of the message, not of the original entity. transfer-coding = "chunked" | transfer-extension transfer-extension = token All transfer-coding values are case-insensitive. HTTP/1.1 uses transfer coding values in the Transfer-Encoding header field (section 14.40). Transfer codings are analogous to the Content-Transfer-Encoding values of MIME , which were designed to enable safe transport of binary data over a 7-bit transport service. However, safe transport has a different focus for an 8bit-clean transfer protocol. In HTTP, the only unsafe characteristic of message-bodies is the difficulty in determining the exact body length (section 7.2.2), or the desire to encrypt data over a shared transport. The chunked encoding modifies the body of a message in order to transfer it as a series of chunks, each with its own size indicator, followed by an optional footer containing entity-header fields. This allows dynamically-produced content to be transferred along with the information necessary for the recipient to verify that it has received the full message. Fielding, et. al. Standards Track [Page 24] RFC 2068 HTTP/1.1 January 1997 Chunked-Body = *chunk "0" CRLF footer CRLF chunk = chunk-size [ chunk-ext ] CRLF chunk-data CRLF hex-no-zero = chunk-size = hex-no-zero *HEX chunk-ext = *( ";" chunk-ext-name [ "=" chunk-ext-value ] ) chunk-ext-name = token chunk-ext-val = token | quoted-string chunk-data = chunk-size(OCTET) footer = *entity-header The chunked encoding is ended by a zero-sized chunk followed by the footer, which is terminated by an empty line. The purpose of the footer is to provide an efficient way to supply information about an entity that is generated dynamically; applications MUST NOT send header fields in the footer which are not explicitly defined as being appropriate for the footer, such as Content-MD5 or future extensions to HTTP for digital signatures or other facilities. An example process for decoding a Chunked-Body is presented in appendix 19.4.6. All HTTP/1.1 applications MUST be able to receive and decode the "chunked" transfer coding, and MUST ignore transfer coding extensions they do not understand. A server which receives an entity-body with a transfer-coding it does not understand SHOULD return 501 (Unimplemented), and close the connection. A server MUST NOT send transfer-codings to an HTTP/1.0 client. 3.7 Media Types HTTP uses Internet Media Types in the Content-Type (section 14.18) and Accept (section 14.1) header fields in order to provide open and extensible data typing and type negotiation. media-type = type "/" subtype *( ";" parameter ) type = token subtype = token Parameters may follow the type/subtype in the form of attribute/value pairs. Fielding, et. al. Standards Track [Page 25] RFC 2068 HTTP/1.1 January 1997 parameter = attribute "=" value attribute = token value = token | quoted-string The type, subtype, and parameter attribute names are case- insensitive. Parameter values may or may not be case-sensitive, depending on the semantics of the parameter name. Linear white space (LWS) MUST NOT be used between the type and subtype, nor between an attribute and its value. User agents that recognize the media-type MUST process (or arrange to be processed by any external applications used to process that type/subtype by the user agent) the parameters for that MIME type as described by that type/subtype definition to the and inform the user of any problems discovered. Note: some older HTTP applications do not recognize media type parameters. When sending data to older HTTP applications, implementations should only use media type parameters when they are required by that type/subtype definition. Media-type values are registered with the Internet Assigned Number Authority (IANA). The media type registration process is outlined in RFC 2048 [17]. Use of non-registered media types is discouraged. 3.7.1 Canonicalization and Text Defaults Internet media types are registered with a canonical form. In general, an entity-body transferred via HTTP messages MUST be represented in the appropriate canonical form prior to its transmission; the exception is "text" types, as defined in the next paragraph. When in canonical form, media subtypes of the "text" type use CRLF as the text line break. HTTP relaxes this requirement and allows the transport of text media with plain CR or LF alone representing a line break when it is done consistently for an entire entity-body. HTTP applications MUST accept CRLF, bare CR, and bare LF as being representative of a line break in text media received via HTTP. In addition, if the text is represented in a character set that does not use octets 13 and 10 for CR and LF respectively, as is the case for some multi-byte character sets, HTTP allows the use of whatever octet sequences are defined by that character set to represent the equivalent of CR and LF for line breaks. This flexibility regarding line breaks applies only to text media in the entity-body; a bare CR or LF MUST NOT be substituted for CRLF within any of the HTTP control structures (such as header fields and multipart boundaries). If an entity-body is encoded with a Content-Encoding, the underlying data MUST be in a form defined above prior to being encoded. Fielding, et. al. Standards Track [Page 26] RFC 2068 HTTP/1.1 January 1997 The "charset" parameter is used with some media types to define the character set (section 3.4) of the data. When no explicit charset parameter is provided by the sender, media subtypes of the "text" type are defined to have a default charset value of "ISO-8859-1" when received via HTTP. Data in character sets other than "ISO-8859-1" or its subsets MUST be labeled with an appropriate charset value. Some HTTP/1.0 software has interpreted a Content-Type header without charset parameter incorrectly to mean "recipient should guess." Senders wishing to defeat this behavior MAY include a charset parameter even when the charset is ISO-8859-1 and SHOULD do so when it is known that it will not confuse the recipient. Unfortunately, some older HTTP/1.0 clients did not deal properly with an explicit charset parameter. HTTP/1.1 recipients MUST respect the charset label provided by the sender; and those user agents that have a provision to "guess" a charset MUST use the charset from the content-type field if they support that charset, rather than the recipient's preference, when initially displaying a document. 3.7.2 Multipart Types MIME provides for a number of "multipart" types -- encapsulations of one or more entities within a single message-body. All multipart types share a common syntax, as defined in MIME [7], and MUST include a boundary parameter as part of the media type value. The message body is itself a protocol element and MUST therefore use only CRLF to represent line breaks between body-parts. Unlike in MIME, the epilogue of any multipart message MUST be empty; HTTP applications MUST NOT transmit the epilogue (even if the original multipart contains an epilogue). In HTTP, multipart body-parts MAY contain header fields which are significant to the meaning of that part. A Content-Location header field (section 14.15) SHOULD be included in the body-part of each enclosed entity that can be identified by a URL. In general, an HTTP user agent SHOULD follow the same or similar behavior as a MIME user agent would upon receipt of a multipart type. If an application receives an unrecognized multipart subtype, the application MUST treat it as being equivalent to "multipart/mixed". Note: The "multipart/form-data" type has been specifically defined for carrying form data suitable for processing via the POST request method, as described in RFC 1867 [15]. Fielding, et. al. Standards Track [Page 27] RFC 2068 HTTP/1.1 January 1997 3.8 Product Tokens Product tokens are used to allow communicating applications to identify themselves by software name and version. Most fields using product tokens also allow sub-products which form a significant part of the application to be listed, separated by whitespace. By convention, the products are listed in order of their significance for identifying the application. product = token ["/" product-version] product-version = token Examples: User-Agent: CERN-LineMode/2.15 libwww/2.17b3 Server: Apache/0.8.4 Product tokens should be short and to the point -- use of them for advertising or other non-essential information is explicitly forbidden. Although any token character may appear in a product- version, this token SHOULD only be used for a version identifier (i.e., successive versions of the same product SHOULD only differ in the product-version portion of the product value). 3.9 Quality Values HTTP content negotiation (section 12) uses short "floating point" numbers to indicate the relative importance ("weight") of various negotiable parameters. A weight is normalized to a real number in the range 0 through 1, where 0 is the minimum and 1 the maximum value. HTTP/1.1 applications MUST NOT generate more than three digits after the decimal point. User configuration of these values SHOULD also be limited in this fashion. qvalue = ( "0" [ "." 0*3DIGIT ] ) | ( "1" [ "." 0*3("0") ] ) "Quality values" is a misnomer, since these values merely represent relative degradation in desired quality. 3.10 Language Tags A language tag identifies a natural language spoken, written, or otherwise conveyed by human beings for communication of information to other human beings. Computer languages are explicitly excluded. HTTP uses language tags within the Accept-Language and Content- Language fields. Fielding, et. al. Standards Track [Page 28] RFC 2068 HTTP/1.1 January 1997 The syntax and registry of HTTP language tags is the same as that defined by RFC 1766 [1]. In summary, a language tag is composed of 1 or more parts: A primary language tag and a possibly empty series of subtags: language-tag = primary-tag *( "-" subtag ) primary-tag = 1*8ALPHA subtag = 1*8ALPHA Whitespace is not allowed within the tag and all tags are case- insensitive. The name space of language tags is administered by the IANA. Example tags include: en, en-US, en-cockney, i-cherokee, x-pig-latin where any two-letter primary-tag is an ISO 639 language abbreviation and any two-letter initial subtag is an ISO 3166 country code. (The last three tags above are not registered tags; all but the last are examples of tags which could be registered in future.) 3.11 Entity Tags Entity tags are used for comparing two or more entities from the same requested resource. HTTP/1.1 uses entity tags in the ETag (section 14.20), If-Match (section 14.25), If-None-Match (section 14.26), and If-Range (section 14.27) header fields. The definition of how they are used and compared as cache validators is in section 13.3.3. An entity tag consists of an opaque quoted string, possibly prefixed by a weakness indicator. entity-tag = [ weak ] opaque-tag weak = "W/" opaque-tag = quoted-string A "strong entity tag" may be shared by two entities of a resource only if they are equivalent by octet equality. A "weak entity tag," indicated by the "W/" prefix, may be shared by two entities of a resource only if the entities are equivalent and could be substituted for each other with no significant change in semantics. A weak entity tag can only be used for weak comparison. An entity tag MUST be unique across all versions of all entities associated with a particular resource. A given entity tag value may be used for entities obtained by requests on different URIs without implying anything about the equivalence of those entities. Fielding, et. al. Standards Track [Page 29] RFC 2068 HTTP/1.1 January 1997 3.12 Range Units HTTP/1.1 allows a client to request that only part (a range of) the response entity be included within the response. HTTP/1.1 uses range units in the Range (section 14.36) and Content-Range (section 14.17) header fields. An entity may be broken down into subranges according to various structural units. range-unit = bytes-unit | other-range-unit bytes-unit = "bytes" other-range-unit = token The only range unit defined by HTTP/1.1 is "bytes". HTTP/1.1 implementations may ignore ranges specified using other units. HTTP/1.1 has been designed to allow implementations of applications that do not depend on knowledge of ranges. 4 HTTP Message 4.1 Message Types HTTP messages consist of requests from client to server and responses from server to client. HTTP-message = Request | Response ; HTTP/1.1 messages Request (section 5) and Response (section 6) messages use the generic message format of RFC 822 [9] for transferring entities (the payload of the message). Both types of message consist of a start-line, one or more header fields (also known as "headers"), an empty line (i.e., a line with nothing preceding the CRLF) indicating the end of the header fields, and an optional message-body. generic-message = start-line *message-header CRLF [ message-body ] start-line = Request-Line | Status-Line In the interest of robustness, servers SHOULD ignore any empty line(s) received where a Request-Line is expected. In other words, if the server is reading the protocol stream at the beginning of a message and receives a CRLF first, it should ignore the CRLF. Fielding, et. al. Standards Track [Page 30] RFC 2068 HTTP/1.1 January 1997 Note: certain buggy HTTP/1.0 client implementations generate an extra CRLF's after a POST request. To restate what is explicitly forbidden by the BNF, an HTTP/1.1 client must not preface or follow a request with an extra CRLF. 4.2 Message Headers HTTP header fields, which include general-header (section 4.5), request-header (section 5.3), response-header (section 6.2), and entity-header (section 7.1) fields, follow the same generic format as that given in Section 3.1 of RFC 822 [9]. Each header field consists of a name followed by a colon (":") and the field value. Field names are case-insensitive. The field value may be preceded by any amount of LWS, though a single SP is preferred. Header fields can be extended over multiple lines by preceding each extra line with at least one SP or HT. Applications SHOULD follow "common form" when generating HTTP constructs, since there might exist some implementations that fail to accept anything beyond the common forms. message-header = field-name ":" [ field-value ] CRLF field-name = token field-value = *( field-content | LWS ) field-content = The order in which header fields with differing field names are received is not significant. However, it is "good practice" to send general-header fields first, followed by request-header or response- header fields, and ending with the entity-header fields. Multiple message-header fields with the same field-name may be present in a message if and only if the entire field-value for that header field is defined as a comma-separated list [i.e., #(values)]. It MUST be possible to combine the multiple header fields into one "field-name: field-value" pair, without changing the semantics of the message, by appending each subsequent field-value to the first, each separated by a comma. The order in which header fields with the same field-name are received is therefore significant to the interpretation of the combined field value, and thus a proxy MUST NOT change the order of these field values when a message is forwarded. Fielding, et. al. Standards Track [Page 31] RFC 2068 HTTP/1.1 January 1997 4.3 Message Body The message-body (if any) of an HTTP message is used to carry the entity-body associated with the request or response. The message-body differs from the entity-body only when a transfer coding has been applied, as indicated by the Transfer-Encoding header field (section 14.40). message-body = entity-body | Transfer-Encoding MUST be used to indicate any transfer codings applied by an application to ensure safe and proper transfer of the message. Transfer-Encoding is a property of the message, not of the entity, and thus can be added or removed by any application along the request/response chain. The rules for when a message-body is allowed in a message differ for requests and responses. The presence of a message-body in a request is signaled by the inclusion of a Content-Length or Transfer-Encoding header field in the request's message-headers. A message-body MAY be included in a request only when the request method (section 5.1.1) allows an entity-body. For response messages, whether or not a message-body is included with a message is dependent on both the request method and the response status code (section 6.1.1). All responses to the HEAD request method MUST NOT include a message-body, even though the presence of entity- header fields might lead one to believe they do. All 1xx (informational), 204 (no content), and 304 (not modified) responses MUST NOT include a message-body. All other responses do include a message-body, although it may be of zero length. 4.4 Message Length When a message-body is included with a message, the length of that body is determined by one of the following (in order of precedence): 1. Any response message which MUST NOT include a message-body (such as the 1xx, 204, and 304 responses and any response to a HEAD request) is always terminated by the first empty line after the header fields, regardless of the entity-header fields present in the message. 2. If a Transfer-Encoding header field (section 14.40) is present and indicates that the "chunked" transfer coding has been applied, then Fielding, et. al. Standards Track [Page 32] RFC 2068 HTTP/1.1 January 1997 the length is defined by the chunked encoding (section 3.6). 3. If a Content-Length header field (section 14.14) is present, its value in bytes represents the length of the message-body. 4. If the message uses the media type "multipart/byteranges", which is self-delimiting, then that defines the length. This media type MUST NOT be used unless the sender knows that the recipient can parse it; the presence in a request of a Range header with multiple byte-range specifiers implies that the client can parse multipart/byteranges responses. 5. By the server closing the connection. (Closing the connection cannot be used to indicate the end of a request body, since that would leave no possibility for the server to send back a response.) For compatibility with HTTP/1.0 applications, HTTP/1.1 requests containing a message-body MUST include a valid Content-Length header field unless the server is known to be HTTP/1.1 compliant. If a request contains a message-body and a Content-Length is not given, the server SHOULD respond with 400 (bad request) if it cannot determine the length of the message, or with 411 (length required) if it wishes to insist on receiving a valid Content-Length. All HTTP/1.1 applications that receive entities MUST accept the "chunked" transfer coding (section 3.6), thus allowing this mechanism to be used for messages when the message length cannot be determined in advance. Messages MUST NOT include both a Content-Length header field and the "chunked" transfer coding. If both are received, the Content-Length MUST be ignored. When a Content-Length is given in a message where a message-body is allowed, its field value MUST exactly match the number of OCTETs in the message-body. HTTP/1.1 user agents MUST notify the user when an invalid length is received and detected. Fielding, et. al. Standards Track [Page 33] RFC 2068 HTTP/1.1 January 1997 4.5 General Header Fields There are a few header fields which have general applicability for both request and response messages, but which do not apply to the entity being transferred. These header fields apply only to the message being transmitted. general-header = Cache-Control ; Section 14.9 | Connection ; Section 14.10 | Date ; Section 14.19 | Pragma ; Section 14.32 | Transfer-Encoding ; Section 14.40 | Upgrade ; Section 14.41 | Via ; Section 14.44 General-header field names can be extended reliably only in combination with a change in the protocol version. However, new or experimental header fields may be given the semantics of general header fields if all parties in the communication recognize them to be general-header fields. Unrecognized header fields are treated as entity-header fields. 5 Request A request message from a client to a server includes, within the first line of that message, the method to be applied to the resource, the identifier of the resource, and the protocol version in use. Request = Request-Line ; Section 5.1 *( general-header ; Section 4.5 | request-header ; Section 5.3 | entity-header ) ; Section 7.1 CRLF [ message-body ] ; Section 7.2 5.1 Request-Line The Request-Line begins with a method token, followed by the Request-URI and the protocol version, and ending with CRLF. The elements are separated by SP characters. No CR or LF are allowed except in the final CRLF sequence. Request-Line = Method SP Request-URI SP HTTP-Version CRLF Fielding, et. al. Standards Track [Page 34] RFC 2068 HTTP/1.1 January 1997 5.1.1 Method The Method token indicates the method to be performed on the resource identified by the Request-URI. The method is case-sensitive. Method = "OPTIONS" ; Section 9.2 | "GET" ; Section 9.3 | "HEAD" ; Section 9.4 | "POST" ; Section 9.5 | "PUT" ; Section 9.6 | "DELETE" ; Section 9.7 | "TRACE" ; Section 9.8 | extension-method extension-method = token The list of methods allowed by a resource can be specified in an Allow header field (section 14.7). The return code of the response always notifies the client whether a method is currently allowed on a resource, since the set of allowed methods can change dynamically. Servers SHOULD return the status code 405 (Method Not Allowed) if the method is known by the server but not allowed for the requested resource, and 501 (Not Implemented) if the method is unrecognized or not implemented by the server. The list of methods known by a server can be listed in a Public response-header field (section 14.35). The methods GET and HEAD MUST be supported by all general-purpose servers. All other methods are optional; however, if the above methods are implemented, they MUST be implemented with the same semantics as those specified in section 9. 5.1.2 Request-URI The Request-URI is a Uniform Resource Identifier (section 3.2) and identifies the resource upon which to apply the request. Request-URI = "*" | absoluteURI | abs_path The three options for Request-URI are dependent on the nature of the request. The asterisk "*" means that the request does not apply to a particular resource, but to the server itself, and is only allowed when the method used does not necessarily apply to a resource. One example would be OPTIONS * HTTP/1.1 The absoluteURI form is required when the request is being made to a proxy. The proxy is requested to forward the request or service it Fielding, et. al. Standards Track [Page 35] RFC 2068 HTTP/1.1 January 1997 from a valid cache, and return the response. Note that the proxy MAY forward the request on to another proxy or directly to the server specified by the absoluteURI. In order to avoid request loops, a proxy MUST be able to recognize all of its server names, including any aliases, local variations, and the numeric IP address. An example Request-Line would be: GET http://www.w3.org/pub/WWW/TheProject.html HTTP/1.1 To allow for transition to absoluteURIs in all requests in future versions of HTTP, all HTTP/1.1 servers MUST accept the absoluteURI form in requests, even though HTTP/1.1 clients will only generate them in requests to proxies. The most common form of Request-URI is that used to identify a resource on an origin server or gateway. In this case the absolute path of the URI MUST be transmitted (see section 3.2.1, abs_path) as the Request-URI, and the network location of the URI (net_loc) MUST be transmitted in a Host header field. For example, a client wishing to retrieve the resource above directly from the origin server would create a TCP connection to port 80 of the host "www.w3.org" and send the lines: GET /pub/WWW/TheProject.html HTTP/1.1 Host: www.w3.org followed by the remainder of the Request. Note that the absolute path cannot be empty; if none is present in the original URI, it MUST be given as "/" (the server root). If a proxy receives a request without any path in the Request-URI and the method specified is capable of supporting the asterisk form of request, then the last proxy on the request chain MUST forward the request with "*" as the final Request-URI. For example, the request OPTIONS http://www.ics.uci.edu:8001 HTTP/1.1 would be forwarded by the proxy as OPTIONS * HTTP/1.1 Host: www.ics.uci.edu:8001 after connecting to port 8001 of host "www.ics.uci.edu". The Request-URI is transmitted in the format specified in section 3.2.1. The origin server MUST decode the Request-URI in order to properly interpret the request. Servers SHOULD respond to invalid Request-URIs with an appropriate status code. Fielding, et. al. Standards Track [Page 36] RFC 2068 HTTP/1.1 January 1997 In requests that they forward, proxies MUST NOT rewrite the "abs_path" part of a Request-URI in any way except as noted above to replace a null abs_path with "*", no matter what the proxy does in its internal implementation. Note: The "no rewrite" rule prevents the proxy from changing the meaning of the request when the origin server is improperly using a non-reserved URL character for a reserved purpose. Implementers should be aware that some pre-HTTP/1.1 proxies have been known to rewrite the Request-URI. 5.2 The Resource Identified by a Request HTTP/1.1 origin servers SHOULD be aware that the exact resource identified by an Internet request is determined by examining both the Request-URI and the Host header field. An origin server that does not allow resources to differ by the requested host MAY ignore the Host header field value. (But see section 19.5.1 for other requirements on Host support in HTTP/1.1.) An origin server that does differentiate resources based on the host requested (sometimes referred to as virtual hosts or vanity hostnames) MUST use the following rules for determining the requested resource on an HTTP/1.1 request: 1. If Request-URI is an absoluteURI, the host is part of the Request-URI. Any Host header field value in the request MUST be ignored. 2. If the Request-URI is not an absoluteURI, and the request includes a Host header field, the host is determined by the Host header field value. 3. If the host as determined by rule 1 or 2 is not a valid host on the server, the response MUST be a 400 (Bad Request) error message. Recipients of an HTTP/1.0 request that lacks a Host header field MAY attempt to use heuristics (e.g., examination of the URI path for something unique to a particular host) in order to determine what exact resource is being requested. 5.3 Request Header Fields The request-header fields allow the client to pass additional information about the request, and about the client itself, to the server. These fields act as request modifiers, with semantics Fielding, et. al. Standards Track [Page 37] RFC 2068 HTTP/1.1 January 1997 equivalent to the parameters on a programming language method invocation. request-header = Accept ; Section 14.1 | Accept-Charset ; Section 14.2 | Accept-Encoding ; Section 14.3 | Accept-Language ; Section 14.4 | Authorization ; Section 14.8 | From ; Section 14.22 | Host ; Section 14.23 | If-Modified-Since ; Section 14.24 | If-Match ; Section 14.25 | If-None-Match ; Section 14.26 | If-Range ; Section 14.27 | If-Unmodified-Since ; Section 14.28 | Max-Forwards ; Section 14.31 | Proxy-Authorization ; Section 14.34 | Range ; Section 14.36 | Referer ; Section 14.37 | User-Agent ; Section 14.42 Request-header field names can be extended reliably only in combination with a change in the protocol version. However, new or experimental header fields MAY be given the semantics of request- header fields if all parties in the communication recognize them to be request-header fields. Unrecognized header fields are treated as entity-header fields. 6 Response After receiving and interpreting a request message, a server responds with an HTTP response message. Response = Status-Line ; Section 6.1 *( general-header ; Section 4.5 | response-header ; Section 6.2 | entity-header ) ; Section 7.1 CRLF [ message-body ] ; Section 7.2 6.1 Status-Line The first line of a Response message is the Status-Line, consisting of the protocol version followed by a numeric status code and its associated textual phrase, with each element separated by SP characters. No CR or LF is allowed except in the final CRLF sequence. Fielding, et. al. Standards Track [Page 38] RFC 2068 HTTP/1.1 January 1997 Status-Line = HTTP-Version SP Status-Code SP Reason-Phrase CRLF 6.1.1 Status Code and Reason Phrase The Status-Code element is a 3-digit integer result code of the attempt to understand and satisfy the request. These codes are fully defined in section 10. The Reason-Phrase is intended to give a short textual description of the Status-Code. The Status-Code is intended for use by automata and the Reason-Phrase is intended for the human user. The client is not required to examine or display the Reason- Phrase. The first digit of the Status-Code defines the class of response. The last two digits do not have any categorization role. There are 5 values for the first digit: o 1xx: Informational - Request received, continuing process o 2xx: Success - The action was successfully received, understood, and accepted o 3xx: Redirection - Further action must be taken in order to complete the request o 4xx: Client Error - The request contains bad syntax or cannot be fulfilled o 5xx: Server Error - The server failed to fulfill an apparently valid request The individual values of the numeric status codes defined for HTTP/1.1, and an example set of corresponding Reason-Phrase's, are presented below. The reason phrases listed here are only recommended -- they may be replaced by local equivalents without affecting the protocol. Status-Code = "100" ; Continue | "101" ; Switching Protocols | "200" ; OK | "201" ; Created | "202" ; Accepted | "203" ; Non-Authoritative Information | "204" ; No Content | "205" ; Reset Content | "206" ; Partial Content | "300" ; Multiple Choices | "301" ; Moved Permanently | "302" ; Moved Temporarily Fielding, et. al. Standards Track [Page 39] RFC 2068 HTTP/1.1 January 1997 | "303" ; See Other | "304" ; Not Modified | "305" ; Use Proxy | "400" ; Bad Request | "401" ; Unauthorized | "402" ; Payment Required | "403" ; Forbidden | "404" ; Not Found | "405" ; Method Not Allowed | "406" ; Not Acceptable | "407" ; Proxy Authentication Required | "408" ; Request Time-out | "409" ; Conflict | "410" ; Gone | "411" ; Length Required | "412" ; Precondition Failed | "413" ; Request Entity Too Large | "414" ; Request-URI Too Large | "415" ; Unsupported Media Type | "500" ; Internal Server Error | "501" ; Not Implemented | "502" ; Bad Gateway | "503" ; Service Unavailable | "504" ; Gateway Time-out | "505" ; HTTP Version not supported | extension-code extension-code = 3DIGIT Reason-Phrase = * HTTP status codes are extensible. HTTP applications are not required to understand the meaning of all registered status codes, though such understanding is obviously desirable. However, applications MUST understand the class of any status code, as indicated by the first digit, and treat any unrecognized response as being equivalent to the x00 status code of that class, with the exception that an unrecognized response MUST NOT be cached. For example, if an unrecognized status code of 431 is received by the client, it can safely assume that there was something wrong with its request and treat the response as if it had received a 400 status code. In such cases, user agents SHOULD present to the user the entity returned with the response, since that entity is likely to include human- readable information which will explain the unusual status. Fielding, et. al. Standards Track [Page 40] RFC 2068 HTTP/1.1 January 1997 6.2 Response Header Fields The response-header fields allow the server to pass additional information about the response which cannot be placed in the Status- Line. These header fields give information about the server and about further access to the resource identified by the Request-URI. response-header = Age ; Section 14.6 | Location ; Section 14.30 | Proxy-Authenticate ; Section 14.33 | Public ; Section 14.35 | Retry-After ; Section 14.38 | Server ; Section 14.39 | Vary ; Section 14.43 | Warning ; Section 14.45 | WWW-Authenticate ; Section 14.46 Response-header field names can be extended reliably only in combination with a change in the protocol version. However, new or experimental header fields MAY be given the semantics of response- header fields if all parties in the communication recognize them to be response-header fields. Unrecognized header fields are treated as entity-header fields. 7 Entity Request and Response messages MAY transfer an entity if not otherwise restricted by the request method or response status code. An entity consists of entity-header fields and an entity-body, although some responses will only include the entity-headers. In this section, both sender and recipient refer to either the client or the server, depending on who sends and who receives the entity. 7.1 Entity Header Fields Entity-header fields define optional metainformation about the entity-body or, if no body is present, about the resource identified by the request. Fielding, et. al. Standards Track [Page 41] RFC 2068 HTTP/1.1 January 1997 entity-header = Allow ; Section 14.7 | Content-Base ; Section 14.11 | Content-Encoding ; Section 14.12 | Content-Language ; Section 14.13 | Content-Length ; Section 14.14 | Content-Location ; Section 14.15 | Content-MD5 ; Section 14.16 | Content-Range ; Section 14.17 | Content-Type ; Section 14.18 | ETag ; Section 14.20 | Expires ; Section 14.21 | Last-Modified ; Section 14.29 | extension-header extension-header = message-header The extension-header mechanism allows additional entity-header fields to be defined without changing the protocol, but these fields cannot be assumed to be recognizable by the recipient. Unrecognized header fields SHOULD be ignored by the recipient and forwarded by proxies. 7.2 Entity Body The entity-body (if any) sent with an HTTP request or response is in a format and encoding defined by the entity-header fields. entity-body = *OCTET An entity-body is only present in a message when a message-body is present, as described in section 4.3. The entity-body is obtained from the message-body by decoding any Transfer-Encoding that may have been applied to ensure safe and proper transfer of the message. 7.2.1 Type When an entity-body is included with a message, the data type of that body is determined via the header fields Content-Type and Content- Encoding. These define a two-layer, ordered encoding model: entity-body := Content-Encoding( Content-Type( data ) ) Content-Type specifies the media type of the underlying data. Content-Encoding may be used to indicate any additional content codings applied to the data, usually for the purpose of data compression, that are a property of the requested resource. There is no default encoding. Fielding, et. al. Standards Track [Page 42] RFC 2068 HTTP/1.1 January 1997 Any HTTP/1.1 message containing an entity-body SHOULD include a Content-Type header field defining the media type of that body. If and only if the media type is not given by a Content-Type field, the recipient MAY attempt to guess the media type via inspection of its content and/or the name extension(s) of the URL used to identify the resource. If the media type remains unknown, the recipient SHOULD treat it as type "application/octet-stream". 7.2.2 Length The length of an entity-body is the length of the message-body after any transfer codings have been removed. Section 4.4 defines how the length of a message-body is determined. 8 Connections 8.1 Persistent Connections 8.1.1 Purpose Prior to persistent connections, a separate TCP connection was established to fetch each URL, increasing the load on HTTP servers and causing congestion on the Internet. The use of inline images and other associated data often requires a client to make multiple requests of the same server in a short amount of time. Analyses of these performance problems are available [30][27]; analysis and results from a prototype implementation are in [26]. Persistent HTTP connections have a number of advantages: o By opening and closing fewer TCP connections, CPU time is saved, and memory used for TCP protocol control blocks is also saved. o HTTP requests and responses can be pipelined on a connection. Pipelining allows a client to make multiple requests without waiting for each response, allowing a single TCP connection to be used much more efficiently, with much lower elapsed time. o Network congestion is reduced by reducing the number of packets caused by TCP opens, and by allowing TCP sufficient time to determine the congestion state of the network. o HTTP can evolve more gracefully; since errors can be reported without the penalty of closing the TCP connection. Clients using future versions of HTTP might optimistically try a new feature, but if communicating with an older server, retry with old semantics after an error is reported. HTTP implementations SHOULD implement persistent connections. Fielding, et. al. Standards Track [Page 43] RFC 2068 HTTP/1.1 January 1997 8.1.2 Overall Operation A significant difference between HTTP/1.1 and earlier versions of HTTP is that persistent connections are the default behavior of any HTTP connection. That is, unless otherwise indicated, the client may assume that the server will maintain a persistent connection. Persistent connections provide a mechanism by which a client and a server can signal the close of a TCP connection. This signaling takes place using the Connection header field. Once a close has been signaled, the client MUST not send any more requests on that connection. 8.1.2.1 Negotiation An HTTP/1.1 server MAY assume that a HTTP/1.1 client intends to maintain a persistent connection unless a Connection header including the connection-token "close" was sent in the request. If the server chooses to close the connection immediately after sending the response, it SHOULD send a Connection header including the connection-token close. An HTTP/1.1 client MAY expect a connection to remain open, but would decide to keep it open based on whether the response from a server contains a Connection header with the connection-token close. In case the client does not want to maintain a connection for more than that request, it SHOULD send a Connection header including the connection-token close. If either the client or the server sends the close token in the Connection header, that request becomes the last one for the connection. Clients and servers SHOULD NOT assume that a persistent connection is maintained for HTTP versions less than 1.1 unless it is explicitly signaled. See section 19.7.1 for more information on backwards compatibility with HTTP/1.0 clients. In order to remain persistent, all messages on the connection must have a self-defined message length (i.e., one not defined by closure of the connection), as described in section 4.4. 8.1.2.2 Pipelining A client that supports persistent connections MAY "pipeline" its requests (i.e., send multiple requests without waiting for each response). A server MUST send its responses to those requests in the same order that the requests were received. Fielding, et. al. Standards Track [Page 44] RFC 2068 HTTP/1.1 January 1997 Clients which assume persistent connections and pipeline immediately after connection establishment SHOULD be prepared to retry their connection if the first pipelined attempt fails. If a client does such a retry, it MUST NOT pipeline before it knows the connection is persistent. Clients MUST also be prepared to resend their requests if the server closes the connection before sending all of the corresponding responses. 8.1.3 Proxy Servers It is especially important that proxies correctly implement the properties of the Connection header field as specified in 14.2.1. The proxy server MUST signal persistent connections separately with its clients and the origin servers (or other proxy servers) that it connects to. Each persistent connection applies to only one transport link. A proxy server MUST NOT establish a persistent connection with an HTTP/1.0 client. 8.1.4 Practical Considerations Servers will usually have some time-out value beyond which they will no longer maintain an inactive connection. Proxy servers might make this a higher value since it is likely that the client will be making more connections through the same server. The use of persistent connections places no requirements on the length of this time-out for either the client or the server. When a client or server wishes to time-out it SHOULD issue a graceful close on the transport connection. Clients and servers SHOULD both constantly watch for the other side of the transport close, and respond to it as appropriate. If a client or server does not detect the other side's close promptly it could cause unnecessary resource drain on the network. A client, server, or proxy MAY close the transport connection at any time. For example, a client MAY have started to send a new request at the same time that the server has decided to close the "idle" connection. From the server's point of view, the connection is being closed while it was idle, but from the client's point of view, a request is in progress. This means that clients, servers, and proxies MUST be able to recover from asynchronous close events. Client software SHOULD reopen the transport connection and retransmit the aborted request without user interaction so long as the request method is idempotent (see section Fielding, et. al. Standards Track [Page 45] RFC 2068 HTTP/1.1 January 1997 9.1.2); other methods MUST NOT be automatically retried, although user agents MAY offer a human operator the choice of retrying the request. However, this automatic retry SHOULD NOT be repeated if the second request fails. Servers SHOULD always respond to at least one request per connection, if at all possible. Servers SHOULD NOT close a connection in the middle of transmitting a response, unless a network or client failure is suspected. Clients that use persistent connections SHOULD limit the number of simultaneous connections that they maintain to a given server. A single-user client SHOULD maintain AT MOST 2 connections with any server or proxy. A proxy SHOULD use up to 2*N connections to another server or proxy, where N is the number of simultaneously active users. These guidelines are intended to improve HTTP response times and avoid congestion of the Internet or other networks. 8.2 Message Transmission Requirements General requirements: o HTTP/1.1 servers SHOULD maintain persistent connections and use TCP's flow control mechanisms to resolve temporary overloads, rather than terminating connections with the expectation that clients will retry. The latter technique can exacerbate network congestion. o An HTTP/1.1 (or later) client sending a message-body SHOULD monitor the network connection for an error status while it is transmitting the request. If the client sees an error status, it SHOULD immediately cease transmitting the body. If the body is being sent using a "chunked" encoding (section 3.6), a zero length chunk and empty footer MAY be used to prematurely mark the end of the message. If the body was preceded by a Content-Length header, the client MUST close the connection. o An HTTP/1.1 (or later) client MUST be prepared to accept a 100 (Continue) status followed by a regular response. o An HTTP/1.1 (or later) server that receives a request from a HTTP/1.0 (or earlier) client MUST NOT transmit the 100 (continue) response; it SHOULD either wait for the request to be completed normally (thus avoiding an interrupted request) or close the connection prematurely. Fielding, et. al. Standards Track [Page 46] RFC 2068 HTTP/1.1 January 1997 Upon receiving a method subject to these requirements from an HTTP/1.1 (or later) client, an HTTP/1.1 (or later) server MUST either respond with 100 (Continue) status and continue to read from the input stream, or respond with an error status. If it responds with an error status, it MAY close the transport (TCP) connection or it MAY continue to read and discard the rest of the request. It MUST NOT perform the requested method if it returns an error status. Clients SHOULD remember the version number of at least the most recently used server; if an HTTP/1.1 client has seen an HTTP/1.1 or later response from the server, and it sees the connection close before receiving any status from the server, the client SHOULD retry the request without user interaction so long as the request method is idempotent (see section 9.1.2); other methods MUST NOT be automatically retried, although user agents MAY offer a human operator the choice of retrying the request.. If the client does retry the request, the client o MUST first send the request header fields, and then o MUST wait for the server to respond with either a 100 (Continue) response, in which case the client should continue, or with an error status. If an HTTP/1.1 client has not seen an HTTP/1.1 or later response from the server, it should assume that the server implements HTTP/1.0 or older and will not use the 100 (Continue) response. If in this case the client sees the connection close before receiving any status from the server, the client SHOULD retry the request. If the client does retry the request to this HTTP/1.0 server, it should use the following "binary exponential backoff" algorithm to be assured of obtaining a reliable response: 1. Initiate a new connection to the server 2. Transmit the request-headers 3. Initialize a variable R to the estimated round-trip time to the server (e.g., based on the time it took to establish the connection), or to a constant value of 5 seconds if the round-trip time is not available. 4. Compute T = R * (2**N), where N is the number of previous retries of this request. 5. Wait either for an error response from the server, or for T seconds (whichever comes first) Fielding, et. al. Standards Track [Page 47] RFC 2068 HTTP/1.1 January 1997 6. If no error response is received, after T seconds transmit the body of the request. 7. If client sees that the connection is closed prematurely, repeat from step 1 until the request is accepted, an error response is received, or the user becomes impatient and terminates the retry process. No matter what the server version, if an error status is received, the client o MUST NOT continue and o MUST close the connection if it has not completed sending the message. An HTTP/1.1 (or later) client that sees the connection close after receiving a 100 (Continue) but before receiving any other status SHOULD retry the request, and need not wait for 100 (Continue) response (but MAY do so if this simplifies the implementation). 9 Method Definitions The set of common methods for HTTP/1.1 is defined below. Although this set can be expanded, additional methods cannot be assumed to share the same semantics for separately extended clients and servers. The Host request-header field (section 14.23) MUST accompany all HTTP/1.1 requests. 9.1 Safe and Idempotent Methods 9.1.1 Safe Methods Implementers should be aware that the software represents the user in their interactions over the Internet, and should be careful to allow the user to be aware of any actions they may take which may have an unexpected significance to themselves or others. In particular, the convention has been established that the GET and HEAD methods should never have the significance of taking an action other than retrieval. These methods should be considered "safe." This allows user agents to represent other methods, such as POST, PUT and DELETE, in a special way, so that the user is made aware of the fact that a possibly unsafe action is being requested. Naturally, it is not possible to ensure that the server does not generate side-effects as a result of performing a GET request; in Fielding, et. al. Standards Track [Page 48] RFC 2068 HTTP/1.1 January 1997 fact, some dynamic resources consider that a feature. The important distinction here is that the user did not request the side-effects, so therefore cannot be held accountable for them. 9.1.2 Idempotent Methods Methods may also have the property of "idempotence" in that (aside from error or expiration issues) the side-effects of N > 0 identical requests is the same as for a single request. The methods GET, HEAD, PUT and DELETE share this property. 9.2 OPTIONS The OPTIONS method represents a request for information about the communication options available on the request/response chain identified by the Request-URI. This method allows the client to determine the options and/or requirements associated with a resource, or the capabilities of a server, without implying a resource action or initiating a resource retrieval. Unless the server's response is an error, the response MUST NOT include entity information other than what can be considered as communication options (e.g., Allow is appropriate, but Content-Type is not). Responses to this method are not cachable. If the Request-URI is an asterisk ("*"), the OPTIONS request is intended to apply to the server as a whole. A 200 response SHOULD include any header fields which indicate optional features implemented by the server (e.g., Public), including any extensions not defined by this specification, in addition to any applicable general or response-header fields. As described in section 5.1.2, an "OPTIONS *" request can be applied through a proxy by specifying the destination server in the Request-URI without any path information. If the Request-URI is not an asterisk, the OPTIONS request applies only to the options that are available when communicating with that resource. A 200 response SHOULD include any header fields which indicate optional features implemented by the server and applicable to that resource (e.g., Allow), including any extensions not defined by this specification, in addition to any applicable general or response-header fields. If the OPTIONS request passes through a proxy, the proxy MUST edit the response to exclude those options which apply to a proxy's capabilities and which are known to be unavailable through that proxy. Fielding, et. al. Standards Track [Page 49] RFC 2068 HTTP/1.1 January 1997 9.3 GET The GET method means retrieve whatever information (in the form of an entity) is identified by the Request-URI. If the Request-URI refers to a data-producing process, it is the produced data which shall be returned as the entity in the response and not the source text of the process, unless that text happens to be the output of the process. The semantics of the GET method change to a "conditional GET" if the request message includes an If-Modified-Since, If-Unmodified-Since, If-Match, If-None-Match, or If-Range header field. A conditional GET method requests that the entity be transferred only under the circumstances described by the conditional header field(s). The conditional GET method is intended to reduce unnecessary network usage by allowing cached entities to be refreshed without requiring multiple requests or transferring data already held by the client. The semantics of the GET method change to a "partial GET" if the request message includes a Range header field. A partial GET requests that only part of the entity be transferred, as described in section 14.36. The partial GET method is intended to reduce unnecessary network usage by allowing partially-retrieved entities to be completed without transferring data already held by the client. The response to a GET request is cachable if and only if it meets the requirements for HTTP caching described in section 13. 9.4 HEAD The HEAD method is identical to GET except that the server MUST NOT return a message-body in the response. The metainformation contained in the HTTP headers in response to a HEAD request SHOULD be identical to the information sent in response to a GET request. This method can be used for obtaining metainformation about the entity implied by the request without transferring the entity-body itself. This method is often used for testing hypertext links for validity, accessibility, and recent modification. The response to a HEAD request may be cachable in the sense that the information contained in the response may be used to update a previously cached entity from that resource. If the new field values indicate that the cached entity differs from the current entity (as would be indicated by a change in Content-Length, Content-MD5, ETag or Last-Modified), then the cache MUST treat the cache entry as stale. Fielding, et. al. Standards Track [Page 50] RFC 2068 HTTP/1.1 January 1997 9.5 POST The POST method is used to request that the destination server accept the entity enclosed in the request as a new subordinate of the resource identified by the Request-URI in the Request-Line. POST is designed to allow a uniform method to cover the following functions: o Annotation of existing resources; o Posting a message to a bulletin board, newsgroup, mailing list, or similar group of articles; o Providing a block of data, such as the result of submitting a form, to a data-handling process; o Extending a database through an append operation. The actual function performed by the POST method is determined by the server and is usually dependent on the Request-URI. The posted entity is subordinate to that URI in the same way that a file is subordinate to a directory containing it, a news article is subordinate to a newsgroup to which it is posted, or a record is subordinate to a database. The action performed by the POST method might not result in a resource that can be identified by a URI. In this case, either 200 (OK) or 204 (No Content) is the appropriate response status, depending on whether or not the response includes an entity that describes the result. If a resource has been created on the origin server, the response SHOULD be 201 (Created) and contain an entity which describes the status of the request and refers to the new resource, and a Location header (see section 14.30). Responses to this method are not cachable, unless the response includes appropriate Cache-Control or Expires header fields. However, the 303 (See Other) response can be used to direct the user agent to retrieve a cachable resource. POST requests must obey the message transmission requirements set out in section 8.2. Fielding, et. al. Standards Track [Page 51] RFC 2068 HTTP/1.1 January 1997 9.6 PUT The PUT method requests that the enclosed entity be stored under the supplied Request-URI. If the Request-URI refers to an already existing resource, the enclosed entity SHOULD be considered as a modified version of the one residing on the origin server. If the Request-URI does not point to an existing resource, and that URI is capable of being defined as a new resource by the requesting user agent, the origin server can create the resource with that URI. If a new resource is created, the origin server MUST inform the user agent via the 201 (Created) response. If an existing resource is modified, either the 200 (OK) or 204 (No Content) response codes SHOULD be sent to indicate successful completion of the request. If the resource could not be created or modified with the Request-URI, an appropriate error response SHOULD be given that reflects the nature of the problem. The recipient of the entity MUST NOT ignore any Content-* (e.g. Content-Range) headers that it does not understand or implement and MUST return a 501 (Not Implemented) response in such cases. If the request passes through a cache and the Request-URI identifies one or more currently cached entities, those entries should be treated as stale. Responses to this method are not cachable. The fundamental difference between the POST and PUT requests is reflected in the different meaning of the Request-URI. The URI in a POST request identifies the resource that will handle the enclosed entity. That resource may be a data-accepting process, a gateway to some other protocol, or a separate entity that accepts annotations. In contrast, the URI in a PUT request identifies the entity enclosed with the request -- the user agent knows what URI is intended and the server MUST NOT attempt to apply the request to some other resource. If the server desires that the request be applied to a different URI, it MUST send a 301 (Moved Permanently) response; the user agent MAY then make its own decision regarding whether or not to redirect the request. A single resource MAY be identified by many different URIs. For example, an article may have a URI for identifying "the current version" which is separate from the URI identifying each particular version. In this case, a PUT request on a general URI may result in several other URIs being defined by the origin server. HTTP/1.1 does not define how a PUT method affects the state of an origin server. PUT requests must obey the message transmission requirements set out in section 8.2. Fielding, et. al. Standards Track [Page 52] RFC 2068 HTTP/1.1 January 1997 9.7 DELETE The DELETE method requests that the origin server delete the resource identified by the Request-URI. This method MAY be overridden by human intervention (or other means) on the origin server. The client cannot be guaranteed that the operation has been carried out, even if the status code returned from the origin server indicates that the action has been completed successfully. However, the server SHOULD not indicate success unless, at the time the response is given, it intends to delete the resource or move it to an inaccessible location. A successful response SHOULD be 200 (OK) if the response includes an entity describing the status, 202 (Accepted) if the action has not yet been enacted, or 204 (No Content) if the response is OK but does not include an entity. If the request passes through a cache and the Request-URI identifies one or more currently cached entities, those entries should be treated as stale. Responses to this method are not cachable. 9.8 TRACE The TRACE method is used to invoke a remote, application-layer loop- back of the request message. The final recipient of the request SHOULD reflect the message received back to the client as the entity-body of a 200 (OK) response. The final recipient is either the origin server or the first proxy or gateway to receive a Max-Forwards value of zero (0) in the request (see section 14.31). A TRACE request MUST NOT include an entity. TRACE allows the client to see what is being received at the other end of the request chain and use that data for testing or diagnostic information. The value of the Via header field (section 14.44) is of particular interest, since it acts as a trace of the request chain. Use of the Max-Forwards header field allows the client to limit the length of the request chain, which is useful for testing a chain of proxies forwarding messages in an infinite loop. If successful, the response SHOULD contain the entire request message in the entity-body, with a Content-Type of "message/http". Responses to this method MUST NOT be cached. 10 Status Code Definitions Each Status-Code is described below, including a description of which method(s) it can follow and any metainformation required in the response. Fielding, et. al. Standards Track [Page 53] RFC 2068 HTTP/1.1 January 1997 10.1 Informational 1xx This class of status code indicates a provisional response, consisting only of the Status-Line and optional headers, and is terminated by an empty line. Since HTTP/1.0 did not define any 1xx status codes, servers MUST NOT send a 1xx response to an HTTP/1.0 client except under experimental conditions. 10.1.1 100 Continue The client may continue with its request. This interim response is used to inform the client that the initial part of the request has been received and has not yet been rejected by the server. The client SHOULD continue by sending the remainder of the request or, if the request has already been completed, ignore this response. The server MUST send a final response after the request has been completed. 10.1.2 101 Switching Protocols The server understands and is willing to comply with the client's request, via the Upgrade message header field (section 14.41), for a change in the application protocol being used on this connection. The server will switch protocols to those defined by the response's Upgrade header field immediately after the empty line which terminates the 101 response. The protocol should only be switched when it is advantageous to do so. For example, switching to a newer version of HTTP is advantageous over older versions, and switching to a real-time, synchronous protocol may be advantageous when delivering resources that use such features. 10.2 Successful 2xx This class of status code indicates that the client's request was successfully received, understood, and accepted. 10.2.1 200 OK The request has succeeded. The information returned with the response is dependent on the method used in the request, for example: GET an entity corresponding to the requested resource is sent in the response; HEAD the entity-header fields corresponding to the requested resource are sent in the response without any message-body; Fielding, et. al. Standards Track [Page 54] RFC 2068 HTTP/1.1 January 1997 POST an entity describing or containing the result of the action; TRACE an entity containing the request message as received by the end server. 10.2.2 201 Created The request has been fulfilled and resulted in a new resource being created. The newly created resource can be referenced by the URI(s) returned in the entity of the response, with the most specific URL for the resource given by a Location header field. The origin server MUST create the resource before returning the 201 status code. If the action cannot be carried out immediately, the server should respond with 202 (Accepted) response instead. 10.2.3 202 Accepted The request has been accepted for processing, but the processing has not been completed. The request MAY or MAY NOT eventually be acted upon, as it MAY be disallowed when processing actually takes place. There is no facility for re-sending a status code from an asynchronous operation such as this. The 202 response is intentionally non-committal. Its p